Genie GS-2669 DC Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 178

background image

Service and Repair Manual

November 2016

Safety Rules

vi

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Personal Safety

Any person working on or around a machine must
be aware of all known safety hazards. Personal
safety and the continued safe operation of the
machine should be your top priority.

Read each procedure thoroughly. This
manual and the decals on the machine,
use signal words to identify the following:

Safety alert symbol—used to alert
personnel to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.

Indicates a imminently hazardous
situation which, if not avoided, will
result in death or serious injury.

Indicates a potentially hazardous
situation which, if not avoided,
could result in death or serious
injury.

Indicates a potentially hazardous
situation which, if not avoided,
may cause minor or moderate
injury.

Indicates a potentially hazardous
situation which, if not avoided,
may result in property damage.

Be sure to wear protective eye wear and
other protective clothing if the situation
warrants it.

Be aware of potential crushing hazards
such as moving parts, free swinging or
unsecured components when lifting or
placing loads. Always wear approved
steel-toed shoes.

Workplace Safety

Any person working on or around a machine must
be aware of all known safety hazards. Personal
safety and the continued safe operation of the
machine should be your top priority.

Be sure to keep sparks, flames and
lighted tobacco away from flammable and
combustible materials like battery gases
and engine fuels. Always have an
approved fire extinguisher within easy
reach.

Be sure that all tools and working areas
are properly maintained and ready for
use. Keep work surfaces clean and free of
debris that could get into machine
components and cause damage.

Be sure any forklift, overhead crane or
other lifting or supporting device is fully
capable of supporting and stabilizing the
weight to be lifted. Use only chains or
straps that are in good condition and of
ample capacity.

Be sure that fasteners intended for one
time use (i.e., cotter pins and self-locking
nuts) are not reused. These components
may fail if they are used a second time.

Be sure to properly dispose of old oil or
other fluids. Use an approved container.
Please be environmentally safe.

Be sure that your workshop or work area
is properly ventilated and well lit.

«
...
4
5
6
7
8
...
»

Содержание GS-2669 DC



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GS-2669 DC

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Sincro Страницы: 24

Бренд: Mopedia Страницы: 36

Бренд: stellar labs Страницы: 52

Бренд: BVM Страницы: 23

Бренд: Sunheat Страницы: 6

Бренд: ADL Embedded Solutions Страницы: 16

Бренд: SeaLevel Страницы: 18

HandyPlasma 250

Бренд: ESAB Страницы: 48

Бренд: PVI Страницы: 12

Бренд: Astra Страницы: 28

SIRIUS 3RA2711-0DB00

Бренд: Siemens Страницы: 9

Бренд: Siemens Страницы: 76

Бренд: Siemens Страницы: 118

SIMOTICS CONNECT 400

Бренд: Siemens Страницы: 120

Бренд: Velux Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды