Genie GS-2669 DC Скачать руководство пользователя страница 119

Страница: 119 / 178

Service and Repair Manual

November 2016

Fault Codes

108

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Type "UXXX" Faults, continued

DTC

Number

Message on

GCON LCD

Description

Possible Causes

Failure Mode

U033

U033:JSTICKFAULT
OUT OF CAL RANGE

PCON drive joystick signal is outside
acceptable calibration.

• PCON drive joystick is not in neutral position range at
system startup.
• PCON joystick.
• GCON ECM.

All drive and steer
functions inhibited.

U034

U034:JSTICKFAULT
OUT OF RANGE:HI

Short circuit of the PCON drive
joystick signal to battery positive at
system startup.

• Short circuit of the PCON drive joystick signal circuit.
• PCON joystick.
• GCON ECM.

All drive and steer
functions inhibited.

U035

U035:JSTICKFAULT
OUT OF RANGE:LO

Short circuit of the PCON drive
joystick signal to battery negative at
system startup.

• Short circuit of the PCON drive joystick signal circuit.
• PCON joystick.
• GCON ECM.

All drive and steer
functions inhibited.

U036

U036:SWITCHFAULT
GCON + PCON:ON

Mis-wiring or short circuit of GCON
key switch.

• Short circuit of the GCON key switch harness.
• GCON key switch.
• GCON ECM.

All functions inhibited.

U037

U037:SWITCHFAULT
FOOTSW PRESSED

Foot switch or Enable switch
depressed at startup.

• Enable switch activated at startup.
• Enable switch contact stuck closed.
• PCON ECM.

All drive and steer
functions inhibited.

U038

U038:SWITCHFAULT
FOOTSWITCH:Bat+

Short circuit of the PCON power
circuit to enable switch to battery
positive.

• Short circuit in PCON power harness.
• Enable switch shorted battery positive.
• PCON ECM.

All drive and steer
functions inhibited.

U039

U039:SWITCHFAULT
FOOTSW:Open/Bat-

Open or short circuit of the PCON
power circuit to enable switch to
battery negative.

• Open or short circuit in PCON power harness.
• Enable switch short or open to battery negative.
• PCON ECM.

All drive and steer
functions inhibited.

U042

U042:SWITCHFAULT
PCON DRIVE MODE

PCON drive mode switch stuck
closed, or depressed prior to startup.

• Drive mode switch stuck closed.
• Drive mode switch is depressed at system startup.
• PCON ECM.

Drive functions inhibited.

U043

U043:SWITCHFAULT
PCON OR MODE

PCON outrigger mode switch stuck
closed, or depressed prior to startup.

• Outrigger mode switch stuck closed.
• Outrigger mode switch is depressed at system startup.
• PCON ECM.

Outrigger extend / retract
function inhibited.

U045

U045:SWITCHFAULT
PCON DRIVE EN

Short circuit of the PCON drive
enable switch at system startup.

• Short circuit of the PCON drive enable switch.
• PCON ECM.
• GCON ECM.

All drive and steer
functions inhibited.

U046

U046:SWITCHFAULT
PCON LIFT MODE

PCON lift mode fault

• PCON lift mode switch is depressed at system startup.
• PCON ECM.

All functions operate
except platform up or
down.

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды