Genie GS-2669 DC Скачать руководство пользователя страница 19

Страница: 19 / 178

Service and Repair Manual

November 2016

Repair Procedures

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Section 3

Repair Pr oc edures

Intr oducti on

Observe and Obey:



Repair procedures shall be completed by a
person trained and qualified on the repair of
this machine.



Immediately tag and remove from service a
damaged or malfunctioning machine.



Repair any machine damage or malfunction
before operating the machine.

Before Repairs Start:



Read, understand and obey the safety rules
and operating instructions in the appropriate
operator's manual on your machine.



Be sure that all necessary tools and parts are
available and ready for use.



Use only Genie approved replacement parts.



Read each procedure completely and adhere
to the instructions. Attempting shortcuts may
produce hazardous conditions.

Machine Configuration:



Unless otherwise specified, perform each
repair procedure with the machine in the
following configuration:

•

Machine parked on a firm, level surface

•

Key switch in the off position with the key

removed

•

The red Emergency Stop button in the off

position at both the ground and platform
controls

•

Wheels chocked

•

All external AC power supply disconnected

from the machine

•

Platform in the stowed position

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды