Genie GS-2669 DC Скачать руководство пользователя страница 55

Страница: 55 / 178

Service and Repair Manual

November 2016

Hydraulic Pump

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

10 Press the Enter button.

Result: The ground controls LCD display will
show the following:

11 Press and Hold the Enter button.

Result: The ground controls LCD display will
scroll through the following screens.

Note: Continue to hold the Enter button until
calibration is complete. If the Enter button is
released, return to step 10 and repeat this
procedure.

Result: The ground controls LCD displays the
following screen. Calibration data is within
range.

Note: The screen will return to the options screen
after 2 seconds.

Result: The ground controls LCD displays the
following screen. Calibration data is not within
range. The pump needs to be repaired or
replaced.

12 For a bad result, press the Enter button to

return to the option screen

13 Push in the red Emergency Stop button to the

off position.

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды