If the Battery becomes discharged and fails to have
sufficient power to start the Engine, jumper cables can
be used to obtain starting assistance. Refer to the Jump
Starting instructions in the Service chapter of this man-
ual for safe jump-start procedure.
FIRST TIME OPERATION
Make sure the Engine is warm and then go through the
following procedures:
Familiarize yourself with various control levers. Raise
the Screed. Control the Paver travel forward and back-
ward, then make left and right turns using the track
control levers and modular steering control. While
stopped, lower the Screed and activate the vibrator.
Divert the exhaust down to the Screed. Position the
Side Gates and Extensions in and out. Raise and lower
the Hopper and turn the Auger Motors on and off.
STOPPING THE PAVER
The following procedure is the recommended
sequence for stopping the machine:
1. Place both Track control Levers in “neutral”.
2. Lower the Hopper and Screed to full “down” posi-
tions.
3. Place all function control Levers in “neutral”.
4. Move the Throttle to “idle” position.
5. Turn the Keyswitch to “off” position. Always
remove the Key and take it with you for security
reasons.
GENERAL PAVER OPERATION
Walk Around Inspection
1. Inspect Suction Hose. Should be firm, not soft.
2. Check for hydraulic leaks.
3. Check Hopper Sides and Floor clearance.
4. Inspect the Screed.
5. Check the safety Guards and Covers.
Hands-On Check
1. Check the Fuel Gauge. Fill the Reservoir before
paving and as necessary.
2. Check the Engine Oil Level and replenish as nec-
essary.
3. Check the cooling air intake on the Radiator
(1649) and the Engine cooling fins (1639).
4. Check the Air Cleaner for cleanliness and make
sure that components are tight to prevent intake of
unfiltered air.
5. Check the fuel Sediment Bowl (1639 Gas Engine)
for cleanliness. Check the Hourmeter against Fuel
Filter change schedule in the Maintenace Log of
this manual.
6. Check the Pump Speed Control Lever for full trav-
el movement.
7. Clean external area of both Tracks (clean 3 to 4
times during working day).
8. Check for and remove as necessary, any asphalt
buildup in the Screed Platform exhaust ports
(located to the front and rear of each end).
CAUTION
Follow the manufacturer recommendations
regarding the use of proper fuel, lubricants
and oil.
To prevent a fire or explosion, allow the
Engine to cool down BEFORE attempting to
refill the Fuel Reservoir. A hot Engine could
ignite the fuel and burn you. Also, do NOT
smoke while refilling the Fuel Reservoir.
CAUTION
Clean external surface of Tracks with asphalt
releasing agent, using the Wash Down
Sprayer. Do NOT spray agent into Tracks
immediately before loading or unloading. Wet
Tracks can slip and lose traction.
CAUTION
Be SURE the area being used for test-running
is clear of spectators and obstructions. For
the first time operate the Paver with an empty
Hopper.
Printed In U.S.A.
25
907389/AP297
Discount-Equipment.com
Содержание PowerBox 1639
