Gehl PowerBox 1639 Скачать руководство пользователя страница 32

Страница: 32 / 66

LUBRICATION LOCATIONS

NOTE:

See the the Service chapter of this

Manual for further details.

Every 10 Hours (or daily)

1. Check Engine Oil Level.
2. Grease Depth Adjustment Screws (2 ea.).

Every 40 Hours (or weekly)

3. Grease Track Adjuster Yoke (1 per Track).
4. Check Hydraulic Fluid Level.

Every 100 Hours

5. Change Hydraulic Filters. (2 ea.).

Every 250 Hours

6. Check Track Torque Hub Fluid Level (2 ea.).
7. Change Engine Oil.

Every 500 Hours

8. Grease Pump Speed Control Linkage (2 ea.).
9. Change Engine Oil Filter.

Every 2000 Hours

10. Change Hydraulic Reservoir Fluid.
11. Clean or Replace Hydraulic Sump Strainer.

Replacement Filters Chart

1649 Diesel Engine

Oil Filter Element

Gehl P/N P700122

Fuel Filter Element

Gehl P/N 123828

1639 Gas Engine

Oil Filter Element

Gehl P/N P221050

In-Line Fuel Filter

Gehl P/N P217000

Hydraulic System Filters

Screw-On Filter Element

Gehl P/N 074830

Reservoir Sump Strainer

Gehl P/N 128299

Air Cleaner

Dry Element (Diesel Eng.)

Gehl P/N 055017

Dry Element (Gas Eng.)

Gehl P/N P700504

Pump Control Lube Details

907389/AP297

Printed In U.S.A.

Discount-Equipment.com

Содержание PowerBox 1639



































































Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды

Gehl PowerBox 1639, Руководство оператора

Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды