Gehl PowerBox 1639 Скачать руководство пользователя страница 39

Страница: 39 / 66

PROBLEM

POSSIBLE CAUSE

REMEDY

System will not operate

1. Oil supply low.

Check oil level and fill.

in either direction

2. Oil Filters clogged.

Replace Filter Element.

3. Oil too heavy.

Use proper viscosity oil.

4. Control linkage misadjusted.

Check to see if control linkage is
binding or unfastened

5. Low charge pressure

See remedy for Causes “6-9”.
Pressure should be 300-350,
100 PSI minimum.

6. Gear pump input shaft damaged.

Inspect gear pump input shaft for

damage.

7. Auxiliary pump charge relief valve

Replace or adjust relief valve.

damaged.

8. Gear pump gears worn or scored.

Replace defective parts.

9. Gear pump damaged.

Disassemble, inspect for damage.

10. Relief valve stuck open.

Remove, clean or replace.

11. Damaged check valve.

Dissassemble and check if valve is
faulty or damaged.

System noisy.

12. Air in system.

Low oil level in Reservoir.

13. Loose suction line.

Tighten fittings or lose hose.

14. Clogged Suction Filter.

Replace Element.

15. Internal Pump or Motor damage.

Dissassemble, inspect, repair or replace.

Sluggish response to

See Cause “12”.

Also see remedy for Causes “1-3, 13”.

acceleration or
decceleration.

See Cause “15”.

16. Low charge pressure.

See remedy for Causes “6, 7, 9”.

17. Relief Valve dirty or damaged.

Remove, clean or replace.

Oil leaking from Pump

18. Defective seal.

Replace seal and/or complete

or Motor.

assembly.

HYDRAULIC PUMP AND MOTORS SYSTEM

Printed In U.S.A.

907389/AP297

Discount-Equipment.com

Содержание PowerBox 1639



































































Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды

Gehl PowerBox 1639, Руководство оператора

Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды