Gehl PowerBox 1639 Скачать руководство пользователя страница 34

Страница: 34 / 66

Chapter 8

TROUBLESHOOTING

CAUTION

Do NOT attempt to service or repair major
components, unless authorized to do so by
your GEHL Dealer. Any Unauthorized Repair
will Void the Warranty.

The following Troubleshooting Guide lists potential
problems, as well as possible causes and remedies, for
the Gehl Paver.

When a problem occurs, don’t overlook simple causes.
A malfunction could be caused by something as simple
as an empty Fuel tank. After a mechanical failure has
been corrected, be sure to locate the cause of the prob-
lem.

PROBLEM

POSSIBLE CAUSE

REMEDY

Engine operation erratic.

Refer to Engine troubleshooting.

Paver difficult to steer.

One forward/reverse lever not fully
engaged.

Engage lever.

NOTE:

Normal lead off to

one side may be as much

Linkage for dual controls binding.

Free up linkage.

as 1 to 2 ft. in 100 ft. of
travel under little or no

Tracks not properly aligned.

Correct alignment.

load conditions

Soft or uneven terrain may

Internal leakage in Modular

Replace seals.

cause lead off which may

Steer Valve.

be interpreted as steering
problems. Actual operating
conditions will cause the
lead off to change.

Paver slowing down or

Engine not running at rated speed.

Disassemble Drive Valve and

excessive power loss.

clean Load Checks.

Check Fuel Filter.

NOTE: Travel speed

Failure of hydraulic system component

Refer to hydraulic component(s)

(0-130 FPM)

(Filter, Motor, Pump, etc.)

troubleshooting.

Hydraulic controls stall to

Hydraulic system leaks.

Locate leaks and correct.

freely or won’t operate
under a load.

Repair faulty component.

Refer to hydraulic components
troubleshooting

GENERAL PAVER PROBLEMS DURING OPERATION

907389/AP297

Printed In U.S.A.

Discount-Equipment.com

Содержание PowerBox 1639



































































Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды

Gehl PowerBox 1639, Руководство оператора

Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды