Gehl PowerBox 1639 Скачать руководство пользователя страница 37

Страница: 37 / 66

PROBLEM

POSSIBLE CAUSE

REMEDY

Tearing of mat

See Causes “3-7”.

(full width)

11. Improper mat thickness.

Mat thickness must be twice size of.
the largest aggregate.

12. Cold mix temperature..

Check with asphalt plant for hotter
asphalt mix.

Mat texture

See Cause “12.

(center or outside streaks)

Mat texture

See Causes “1, 3-6, 11, 12”.

(non uniform)

Screed marks

See Causes “7, 8”.

Screed not responding

See Causes “6, 11, 12”.

to correction

Auger shadows

See Causes “3-5”.

Poor pre-compaction

See Causes “1, 11, 12”.

Poor longitudinal or

See Causes “2, 12”.

transverse joint.

Transvers cracking

See Causes “1-4, 6, 13”.

(checking).

Mat shoving under

See Causes “1-4, 6, 9, 13”.

Roller.

Bleeding or fat spots

See Cause “3, 4, 6, 13”.

in mat.

Roller marks.

See Causes “1, 2, 6, 9, 10”.

Poor mix compaction.

See Causes “1-4, 6, 9, 10, 12, 13”.

MATERIAL-DELIVERY-COMPACTION RELATED MAT PROBLEMS (Cont.)

Printed In U.S.A.

907389/AP297

Discount-Equipment.com

Содержание PowerBox 1639



































































Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды

Gehl PowerBox 1639, Руководство оператора

Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды