Table of Contents
5
1
Introduction ..........................................................................................................
6
1.1
About this manual ................................................................................................................................
7
1.2
Important user information .............................................................................................................
9
1.3
Regulatory information ......................................................................................................................
12
1.4
Associated documentation ..............................................................................................................
13
2
Safety instructions ...............................................................................................
14
2.1
Safety precautions ...............................................................................................................................
20
2.2
Labels .........................................................................................................................................................
22
2.3
Emergency procedures ......................................................................................................................
24
2.4
Recycling information .........................................................................................................................
25
2.5
Declaration of Hazardous Substances (DoHS) ........................................................................
27
3
System description ..............................................................................................
28
3.1
Illustrations of Ettan IPGphor 3 ......................................................................................................
32
3.2
Ettan IPGphor 3 instrument .............................................................................................................
34
3.3
Ettan IPGphor 3 Control Software .................................................................................................
35
3.4
Strip holders ............................................................................................................................................
37
4
Installation ............................................................................................................
38
4.1
Site requirements ..................................................................................................................................
40
4.2
Unpacking and transport ..................................................................................................................
41
4.3
Setup ...........................................................................................................................................................
45
4.4
Software installation for isoelectric focusing process .........................................................
46
Operation ..............................................................................................................
47
5.1
Preparations before start ..................................................................................................................
48
5.1.1
Use the strip holders .....................................................................................................................
59
5.1.2
Use the Ettan IPGphor Cup Loading Manifold ...................................................................
66
5.2
Start up the instrument .....................................................................................................................
68
5.3
Perform a run from the control panel .........................................................................................
69
5.3.1
Ettan IPGphor 3 control panel functionality .......................................................................
73
5.3.2
Protocol parameters .....................................................................................................................
75
5.3.3
Set protocol parameters .............................................................................................................
83
5.3.4
Isoelectric focusing from the control panel ........................................................................
89
5.3.5
Pause or stop a protocol .............................................................................................................
90
5.4
Run a pre-programmed protocol from the PC ........................................................................
91
5.4.1
Setting up a run ..............................................................................................................................
97
5.4.2
Perform a run ..................................................................................................................................
102
Maintenance .........................................................................................................
103
6.1
Cleaning Ettan IPGphor 3 ..................................................................................................................
107
6.2
Replace fuses ..........................................................................................................................................
Ettan IPGphor 3 Operating Instructions 28-9635-51 AC
