GE Ettan IPGphor 3 Скачать руководство пользователя страница 97

Страница: 97 / 120

5.4.2

Perform a run

Start a run

Follow the instructions below to start the run after transferring the protocol.

Action

Step

Select instrument by clicking the desired Instrument selection button (Instr1-
Instr4).

Select a protocol to run.

Select the number of strips to run.

Click Start button.

The current protocol is now downloaded to position 1 in the selected instru-
ment.

The run is now started which is indicated by the word Running below the
instrument control buttons.

To start a second run, select the desired instrument, protocol, and number
of strips to run, and click Start button. It is possible to start up to four different
runs using four different protocols on four different instruments in parallel.

Ettan IPGphor 3 Operating Instructions 28-9635-51 AC

5 Operation

5.4 Run a pre-programmed protocol from the PC

5.4.2 Perform a run

Содержание Ettan IPGphor 3

























































































































Результаты поиска

Содержание Ettan IPGphor 3

Отзывы:

Бренды по названию

Популярные бренды

GE Ettan IPGphor 3, Руководство по эксплуатации

Результаты поиска

Содержание Ettan IPGphor 3

Отзывы:

Бренды по названию

Популярные бренды