GE Druck ADTS 505 Скачать руководство пользователя страница 83

Страница: 83 / 124

Druck ADTS 505 User Manual

6 - 3

K0260 Issue No. 8

MACH Pt

•

In aeronautical units (ft/kts or m/km/h), this key selects the Mach display.

•

In pressure units (mbar, inHg etc.), this key selects the total pressure (Pt) display.

•

If the altitude aim is changed, after the entry of CAS, the Mach aim value changes while the
CAS value remains unchanged.

•

If the altitude aim is changed, after the entry of Mach, the CAS aim value changes while the
Mach value remains unchanged.

•

If the Ps aim is changed, after the entry of Qc, then the Pt aim value changes while the Qc
remains unchanged.

•

If the Ps aim is changed, after the entry of Pt, then the Qc aim value changes while the Pt
remains unchanged.

•

When in Control Mode (AIM display), a new Mach or Pt aim can be entered using the numeric
keys, Use

LEAK MEASURE/CONTROL

to change between Control and Leak Measure mode.

ROC Ps RATE

•

In aeronautical units (ft or m), this key selects the Rate of Climb (ROC) or vertical speed
display.

•

In pressure units (mbar, inHg etc.), this key selects the rate of change of Ps display.

•

Select [UNITS], from the main menu, to change between aeronautical and pressure units.

•

When in Control Mode (AIM display), a new ROC or Ps rate can be entered using the numeric
keys. Use

LEAK MEASURE/CONTROL

to change between Control and Leak Measure mode.

The default control rate set at manufacture is 3000 ft/min.

Содержание Druck ADTS 505





























































































































Результаты поиска

Содержание Druck ADTS 505

Отзывы:

GE Druck ADTS 505, Руководство пользователя, Страница: 83 / 124

Результаты поиска

Содержание Druck ADTS 505

Отзывы: