GE Druck ADTS 505 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 124

GE Druck ADTS 505 Скачать руководство пользователя страница 30

3 - 2

Operation

K0260 Issue No. 8

3.2

Display Functions and Units of Measure

When operating in either pressure measuring or pressure controlling modes, the ADTS 505 can
display the following information:

Aeronautical Functions

Display Abbreviation

Displayed Units

(if applicable)

Altitude

ALT

ft, m

Calibrated Airspeed

CAS

kts, km/h, mph

Mach

MACH

-

Rate of Climb

ROC

ft/min, m/min, m/s, hm/min

Rate of Airspeed

Rt CAS

kts/min, km/h/min, mph/min

Pressure Functions

Display Abbreviation

Displayed Units

(if applicable)

Static (Absolute)

Ps

[P]

Pitot (Absolute)

Pt

[P]

Dynamic or Impact
(Differential)

Qc

[P]

Engine Pressure Ratio

EPR

-

Rate of Ps

Rt Ps

[P]

/min

Rate of Pt

Rt Pt

[P]

/min

Rate of Qc

Rt Qc

[P]

/min

Rate of EPR

Rt EPR

EPR/min

Where

[P]

is the currently selected pressure units from the following list:

mbar, inHg, mmHg, inH

2

O (4°C), inH

2

O (20°C), inH

2

O (60°F), psi, hPa, kPa.

Operating Range and Performance

The ADTS 505 is supplied with a full-scale range of 650 knots for measurement and control of the
pitot pressure channel. The unit can measure altitude up to 105,000 ft; altitude control depends
on the performance of the pump, the integral pump is capable of achieving -2000 to 60,000 ft.
Refer to section 6 for more details of performance and specification.

Sets of factory-defined limits known as ARINC565, Standard, Military, Max and EPR can be selected
through the SETUP menu (see Reference section 6). Operators may also define up to five sets of
additional limits for different aircraft types. When configuring the display to aeronautical or
pressure units operators should be aware that when units of pressure are selected, wider full-scale
pressure limits will be enabled for some parameters.

«
...
28
29
30
31
32
...
»

Содержание Druck ADTS 505





























































































































Отзывы:

Нет отзывов