GE Druck ADTS 505 Скачать руководство пользователя страница 123

Страница: 123 / 124

Druck ADTS 505 User Manual

6 - 43

K0260 Issue No. 8

Performance expressed in pressure units

OTES

(1)

Maximum operating range can be achieved using the internal pump at airfield altitudes
to a maximum of 7,500 ft above sea level.

(2)

The accuracy figures stated include 12 months stability.

(3)

The system measures below this value but, because of pump capacity, controls to 71.7
mbar absolute. 35 mbar is the lowest calibration point.

Max Pt 3000 mbar absolute (with Ps >500 mbar absolute)
Max Qc 2500 mbar differential (with Ps <500 mbar absolute)

Altitude Sensor

(Ps)

Airspeed Sensor

(Qc)

EPR

Units

mbar abs

inHg abs

mbar diff

inHg diff

Maximum Range

(1)

71.7

(3)

to 1355

2.1 to 40

-950 to +2490

1 to 73.53

0.1 to 10

Accuracy

(2)

±0.1

±0.003

±0.1% reading

±0.125 mbar

±0.1% reading

±0.0037 inHg

Better than

0.005

Repeatability

±0.05

±0.0015

±0.05 rising to 0.17

±0.0015 rising to 0.0051

Resolution

0.01

0.0003

0.01

0.0003

0.001

Содержание Druck ADTS 505





























































































































Результаты поиска

Содержание Druck ADTS 505

Отзывы:

GE Druck ADTS 505, Руководство пользователя, Страница: 123 / 124

Результаты поиска

Содержание Druck ADTS 505

Отзывы: