Fujitsu ABHG54KRTA Скачать руководство пользователя

Страница: 122 / 154



Overflow control

•

Triggering condition

The float switch is turned on.

•

Operation details

– The drain pump is turned on.
– When the operation mode is cooling or dry, operate the followings.

• The compressor is stopped.
• Then indoor fan control is turned off.

•

Release condition

– The float switch is turned off.

• In the case that on the cooling or dry mode the thermostat is on, refer to "

During the com-

pressor in operation

" for the operation after release.

• In other case, refer to "

When the compressor is not in operation

" for the operation after

release.

– 3 minutes passed

•

Operation after release

The compressor stopps permanently.



The compressor is stopped by Anti-freezing control

•

Triggering condition

During the compressor in operation, the compressor is stopped by Anti-freezing control.

•

Operation details

The drain pump is kept on in 60 minutes after Anti-freezing control released.

•

Release condition

60 minutes passed

•

Operation after release

According to the settings, operate the followings.

Off

a. Operation at
anti-freezing

b. Operation when
cooling mode is
stopped

Operation at
a. and b.

117

(min)

117

Anti-freezing start

Stopped

Release
freezing

7-9. Drain pump control

- (04-24) -

7. Various control

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

Содержание ABHG54KRTA



























































































































































Результаты поиска

Содержание ABHG54KRTA

Отзывы:

Похожие инструкции для ABHG54KRTA

Бренды по названию

Популярные бренды

Fujitsu ABHG54KRTA, Руководство по обслуживанию

Результаты поиска

Содержание ABHG54KRTA

Отзывы:

Похожие инструкции для ABHG54KRTA

Бренды по названию

Популярные бренды