Fujitsu ABHG54KRTA Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 154

background image

2. Auto changeover operation

When the air conditioner is set to AUTO mode by remote controller, operation starts in the optimum
mode from among heating, cooling, dry and monitoring modes. During operation, the optimum mode
is automatically switched in accordance with temperature changes. The temperature can be set be-
tween 18°C and 30°C in 1.0°C steps.

• When operation starts, indoor fan and outdoor fan are operated for around 1 minute.

Room temperature and outdoor temperature are sensed, and the operation mode is selected in
accordance with the table below.

Room temperature

Operation mode

Tr > Ts + 2°C

Cooling

Ts + 2°C ≥ Tr ≥ Ts - 2°C

Middle zone

Tr < Ts - 2°C

Heating

Tr: Room temperature
Ts: Setting temperature

NOTE:

When the operation mode is middle zone, indoor unit operation mode is selected as below.

• Same operation mode is selected as outdoor unit.

If outdoor unit is operating in cooling and heating mode, indoor unit will be operated by
the same operation mode.

• Selected by outdoor temperature.

If outdoor unit is operating in other than cooling and heating mode, indoor unit will be op-
erated according to the outdoor temperature as below.

Outdoor temp.

Operation mode

25°C or more

Cooling

Less than 25°C

Heating

• When the compressor was stopped for 6 consecutive minutes by temperature control function af-

ter the cooling or heating mode was selected as above, operation is switched to monitoring mode
and the operation mode selection is done again.

• When the middle zone is selected on the predetermining of the operation mode, the operation

mode before the changing to the monitoring mode is selected.

- (04-6) -

2. Auto changeover operation

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

«
...
102
103
104
105
106
...
»

Содержание ABHG54KRTA



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для ABHG54KRTA

MCM-A200 User Manual (XP)

Бренд: Samsung Страницы: 12

Бренд: QuietFlo Страницы: 24

Бренд: Omega Страницы: 56

Бренд: Tecnoclima Страницы: 40

Бренд: Clatronic Страницы: 62

Бренд: edc Страницы: 46

Бренд: Fedders Страницы: 75

Бренд: Daikin Страницы: 6

Бренд: mundoclima Страницы: 14

ECOLIGHT 12000 IU

Бренд: Argo Страницы: 64

Бренд: Olimpia splendid Страницы: 180

Бренд: Daikin Страницы: 19

purehot+cool link

Бренд: Dyson Страницы: 136

Бренд: ARDES Страницы: 20

Бренд: Russell Hobbs Страницы: 32

Бренд: Jata Страницы: 16

Бренд: Jata Страницы: 16

Бренд: Daikin Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды