Fujitsu ABHG54KRTA Скачать руководство пользователя

Страница: 121 / 154

7-9. Drain pump control

Drain control for cooling operation



During the compressor in operation

•

Triggering condition

The thermostat is turned on during cooling or dry mode.

•

Operation details

The drain pump is turned on.

•

Release condition

– The thermostat is turned off.

Refer to "

When the compressor is not in operation

" for the operation after release.

– The compressor is stopped.

Refer to "

When the compressor is not in operation

" for the operation after release.

– The operation is switched to heating mode.

Refer to "

When the compressor is not in operation

" for the operation after release.

– The float switch is turned on.

Refer to "

Overflow control

" for the operation after release.

– The compressor is stopped by Anti-freezing control.

Refer to "

The compressor is stopped by Anti-freezing control

" for the operation after re-

lease.



When the compressor is not in operation

•

Triggering condition

– The thermostat is turned off.
– The compressor is stopped.
– The operation is switched to heating mode.
– The float switch is turned off.

•

Operation details

– Count 180 minutes.
– Start drain pump intermittent operaion.

Off

Drain pump

3 min

Trigger point
(0 min)

3 min

10 min

60 min

180 min

•

Release condition

– 3 minutes drain pump operation is finished after 180 minutes count.
– The operation is switched to cooling or dry mode.

Refer to "

During the compressor in operation

" for the operation after release.

– The float switch is turned on.

Refer to "

Overflow control

" for the operation after release.

•

Operation after release

The drain pump is turned off and the air conditioner operate according the settings.

7-9. Drain pump control

- (04-23) -

7. Various control

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

Содержание ABHG54KRTA



























































































































































Результаты поиска

Содержание ABHG54KRTA

Отзывы:

Похожие инструкции для ABHG54KRTA

Бренды по названию

Популярные бренды

Fujitsu ABHG54KRTA, Руководство по обслуживанию

Результаты поиска

Содержание ABHG54KRTA

Отзывы:

Похожие инструкции для ABHG54KRTA

Бренды по названию

Популярные бренды