Fuji Electric Time Delta-C FSV-2, Инструкция по эксплуатации

Страница: 137 / 149

-130-
<Parameter specification table Measurement mode: 2-path >
Setting item Initial value Setting value Setting range
ID No 0000 ID No. is invalid when 0000 is selected.
Language Japanese English, Japanese, German, French, Spanish
Measurement mode 2 path 1 path, 2 path, 2 pipes
Calculation output Average Average, Addition, Sub (CH1-CH2),
Sub (CH2-CH1)
Action mode Normal Normal, High speed
System unit Metric Metric or Inch
Flow unit
㎥
/h L/s
，
L/min
，
L/h
，
L/d
，
kL/d
，
ML/d
，
m
3
/s
，
m
3
/min
，
m
3
/h
，
m
3
/d
，
km
3
/d
，
Mm
3
/d
，
BBL/s
，
BBL/min
，
BBL/h
，
BBL/d
，
kBBL/d
，
MBBL/d
Unit
Total unit
㎥
mL
，
L
，
m
3
，
km
3
，
Mm
3
，
mBBL
，
BBL
，
kBBL
Outer diameter 60.00mm 6.00 to 6200.00mm
Pipe material PVC Carbon steel, Stainless, PVC, Copper, Cast
iron, Aluminum, FRP, Ductile iron, PEEK,
PVDF, Acrylic and PP
Pipe sound velocity
(Sound velocity: [m/s, ft/s])
Wall thickness 4.00mm 4.00mm
Lining material No lining No lining, Tar epoxy, Mortar, Rubber, Teflon,
Pyrex glass, PVC
Lining S.V. (Sound velocity: [m/s, ft/s])
Lining thickness ― 0.01 to 100.00mm
Kind of fluid Water Water, seawater, dist. water, ammonia, alcohol,
benzene, bromide, ethanol, glycol, kerosene,
milk, methanol, toluol, lube oil, fuel oil, petrol
and refrigerant R410
Fluid S.V. (Sound velocity: [m/s, ft/s])
Viscosity
1.0038×10
-6
㎡
/s
0.001 to 999.999×10
-6
m
2
/s
Sensor mounting method V method V method, Z method
Measuring conditions
Pr
ocess setting
Sensor type FSSA FSSA/FSSG,FLS_12/FLS_22,FSSC,FSG_32,
FSG_31/FSG_41,FSSE/FSG_50FSSF/FSG_51,
FSD12,FSSD/FSD22,FSSH/FSD32
Damping 5.0 sec 0.0 to 100.0sec
Low flow cut
0.15
㎥
/h
0 to 5m/s in terms of flow velocity
Analog output 1 source
channel CH1: Flow rate CH1: Flow rate, CH2: Flow rate, CH3: Flow rate
(Note2)
Analog output 2 source
channel CH2: Flow rate CH1: Flow rate, CH2: Flow rate, CH3: Flow rate
(Note2)
Kind Flow rate Velocity, Flow rate
Range type Single Single, Auto 2, Bi-dir, Bi-dir Auto 2
Full scale 1
15.000
㎥
/h
0, ±0.3 to ±32m/s in terms of flow velocity
Full scale 2
0.000
㎥
/h
0, ±0.3 to ±32m/s in terms of flow velocity
Hysteresis 10.00 % 0.00 to 20.00%
Burnout (current) Hold Not used, Hold, Lower, Upper and Zero
Burnout timer 10 sec 10 to 900sec
Output limit low -20 % -20 to 0%
Analog output
Output limit high 120 % 100 to 120%
Total mode Stop Start, Stop, Reset
Total rate
0
㎥
0.000000 to 99999999
Total preset
0 ㎥
0.000000 to 99999999
Pulse width 50msec 5msec
，
10msec
，
50msec
，
100msec
，
200msec
，
500msec
，
1000msec
Burnout (total) Hold Not used, Hold
To
ta
l output
Burnout timer 10 sec 10 to 900sec
DO1 source channel CH1 CH1
，
CH2
，
CH3
DO1 output type Not used Not used, +Total pulse, -Total pulse, Full scale 2,
Alarm [All, Hardware fault, Process error]
Flow switch
 Flow SW high [ ]
 Flow SW low [ ],
Total switch [ ],
AO range over, Pulse range over, –Flow direction
DO1 output operation Active ON Active ON, Active OFF
DO2 source channel CH1
CH1
，
CH2
，
CH3
DO2 output type Not used Same as “DO1 output type”
DO2 output operation Active ON Active ON, Active OFF
DO3 source channel CH1 CH1
，
CH2
，
CH3
DO3 output type Not used Same as “DO1 output type”
DO3 output operation Active ON Active ON, Active OFF
DO4 source channel CH1
CH1
，
CH2
，
CH3
DO4 output type Not used Same as “DO1 output type”
Output condition
s
Cont
act output
DO4 output operation Active ON Active ON, Active OFF