Ford Granada 1985-1994, Руководство пользователя

Страница: 183 / 254

the door through the large cut-out. Further
displacement or removal of the foam rubber
sheet may be necessary.
7 Refit in the reverse order to removal, noting
the following points:
a) Apply a little grease to the interior handle
rods where they pass through the plastic
bushes
b) When securing the interior handle, have
the locking lever in the “unlocked”
position, hold the assembly forwards as
far as it will go and tighten the securing
screw
c) Check all functions before refitting the trim
panel.
Door weatherstrip
1 Open the door and remove the weatherstrip
securing screw from the latch end. In the case
of the rear door, also remove the screw from
the hinge end.
2 Carefully lift the latch end of the
weatherstrip and pull it off the door.
3 Refit by reversing the removal operations,
using your palm to seat the weatherstrip.
Aperture weatherstrip
4 Open the door. Remove the scuff plate
securing screws from the bottom of the door
aperture.
5 Pull the old weatherstrip out of the door
aperture.
6 Fit the new weatherstrip, starting at the
right-angled corner at the top. Fit the
weatherstrip to the other corners and bends,
leaving the straight sections until last.
7 Refit the scuff, plate securing screws.
All models except Estate
1 Disconnect the battery negative lead.
2 Remove the tailgate interior trim panel,
which is secured by eleven screws.
3 Remove the six nuts which secure the
tailgate handle. Remove the handle and
recover the gasket.
4 Disconnect the tailgate lock switch multi-
plug. Release the switch locking tab and
remove the switch.
5 Disconnect the operating rod from the lock
lever (see illustration). Extract the U-clip and
remove the lock barrel.
6 Refit by reversing the removal operations.
Estate models
7 The tailgate lock barrel can be removed and
refitted as described above, bearing in mind
the notes made in Section 8 when removing
the interior trim panels and noting that the lock
assembly is retained by two Torx bolts.
1 Open up the boot lid and remove the trim
panel from the inside of the lid.
2 Unscrew the four boot lid exterior trim
retaining panel bolts (two situated on each
side of the lock) then carefully prise out the
nine panel retaining clips and remove the
panel from the boot lid.
3 Undo the two lock barrel retaining nuts then
partially withdraw the barrel and disconnect the
wiring connector and lock operating rod from
the barrel. Remove the lock barrel from the lid.
4 Undo the four lid lock retaining bolts then
withdraw the lock assembly from the boot lid,
disconnecting the central locking and warning
switch wiring plugs (see illustration).
5 Refitting is a reversal of the removal
procedure tightening all retaining bolts
securely. On completion check the operation
of the boot lid lock and lock barrel before
refitting the trim panel.
1 Disconnect the battery negative lead.
2 Remove the tailgate interior trim panel,
which is secured by eleven screws.
3 Unhook the operating rod from the tailgate
latch. Also disconnect the lock switch and
solenoid multi-plugs.
4 Remove the three bolts which secure the
tailgate latch. Remove the latch.
5 Refit by reversing the removal operations.
1 Open the tailgate and support it with a piece
of wood.
2 Release the strut from its mountings by
raising the spring clips with a small
screwdriver, then pulling the strut off the ball-
stands. Do not raise the clips more than 4 mm
(0.16 in) if the strut is to be re-used.
3 Do not attempt to dismantle a strut, and
dispose of it safely. It contains gas under
pressure.
4 To refit a strut, position it over the ball-
studs. Push on each end in turn until it snaps
home.
1 Open the fuel filler flap. Remove the key.
2 Apply pressure to the lock barrel at the key
slot, using the thumb of one hand. With the
other hand insert a screwdriver into the cut-
out in the filler flap to release the lock barrel
retaining spring. As the spring is released,
thumb pressure will eject the lock barrel into
the petrol tank (see illustration).
3 To refit, push the lock barrel into the flap
until the retaining spring clicks home.
Front door
1 Open the door and remove the screws
which secure the front and rear edges of the
trim panel (see illustration).
2 Remove the two screws from under the
covers on the door pocket. Unclip and remove
the pocket.
3 On models with electrically-operated
windows and mirrors, prise out and disconnect
the window and mirror switches. The window
switch multi-plugs on the driver’s side are
22 Door interior trim panel -
removal and refitting
21 Fuel filler lock barrel -
removal and refitting
20 Tailgate strut - removal and
refitting
19 Tailgate latch assembly -
removal and refitting
18 Boot lid lock barrel - removal
and refitting
17 Tailgate lock barrel - removal
and refitting
16 Door weatherstrip - removal
and refitting
Bodywork and fittings 12•7
12
17.5 Operating rod (arrowed) connected to
tailgate lock lever
18.4 Boot lid lock retaining bolts (arrowed)
- Saloon models
21.2 Removing the fuel filler flap lock barrel