Ford Granada 1985-1994, Руководство пользователя

Страница: 182 / 254

3 Apply masking tape to the front and sides of
the roof aperture to protect the paintwork.
4 Close the roof. Remove the Torx screw
which secures the operating handle,
counterholding the handle whilst slackening
the screw (see illustration). Remove the
operating handle.
5 With the aid of an assistant, remove the
sliding roof assembly by pushing it up from
inside and drawing it forwards from outside.
Support the rear of the roof as it is removed.
6 Refit by reversing the removal operations.
1 If the release cable has broken, the bonnet
catch can be released from below with the aid of
a long screwdriver. It will be necessary to raise
and support the front of the vehicle for access.
With the bonnet open, proceed as follows.
2 Remove the steering column lower shroud.
3 Disconnect the cable from the release lever
by pulling the cable outer from the bracket,
then unhooking the inner from the lever (see
illustration).
4 Pull the cable through the bulkhead
grommet into the engine bay. Release the
cable from any clips or ties.
5 Disengage the inner and outer cables from
the bonnet catch (see illustration). Remove
the cable.
6 Refit by reversing the removal operations,
being careful not to kink or bend the cable.
Check that operation of the release lever causes
the catch to move before closing the bonnet.
1 Open the door and slacken the two Torx
screws which secure the striker plate. The
screws should be loosened until the plate can
be moved by tapping, but not by hand pressure.
2 Move the striker plate if necessary until it is
aligned with the centre of the latch opening
(see illustration).
3 Open and close the door a few times until the
locking action is smooth and the door position
when shut is satisfactory. Then open the door
again and tighten the striker plate screws.
1 Remove the door interior trim panel.
2 Carefully peel away the foam rubber sheet
in the area of the door handle operating rod.
Disconnect the rod from the handle.
3 Remove the two screws which secure the
handle to the door, then remove the handle.
4 Refit by reversing the removal operations.
1 Remove the door interior trim panel.
2 Carefully peel away the foam rubber sheet
in the area of the lock barrel. Unhook the
operating rod from the lock barrel lever (see
illustration).
3 When so equipped, unclip the switch from
the lock barrel and disconnect its wiring.
4 Remove the large U-clip which secures the
lock barrel to the door. Remove the barrel.
5 Refit by reversing the removal operations.
Check the lock for correct operation before
refitting the door trim.
1 Remove the door interior trim panel.
2 Carefully peel away the foam rubber sheet
in the area of the door latch. Unhook the lock
barrel operating rod from the latch. Also
unhook the exterior handle operating rod.
3 Disconnect the lock motor multi-plug (when
fitted). Remove the two screws to release the
lock motor. Pivot the motor to release the
operating rod from it.
4 Remove the door interior handle securing
screw (see illustration). Slide the handle
rearwards to release it from the door. Unhook
the rods from the handle and release them
from their bushes.
5 When door latch switches are fitted,
disconnect the switch multi-plug.
6 Remove the three screws which secure the
door latch (see illustration). Manoeuvre the
latch behind the window channel and out of
15 Door latch assembly -
removal and refitting
14 Door lock barrel - removal
and refitting
13 Door exterior handle -
removal and refitting
12 Door striker plate - adjustment
11 Bonnet release cable -
removal and refitting
12•6 Bodywork and fittings
11.3 Unhooking the cable inner from the
release lever
14.2 Unhook the operating rod (arrowed)
from the lock barrel lever
15.4 Door interior handle securing screw
(arrowed)
15.6 Door latch securing screws
11.5 Bonnet release cable connected to
catch
12.2 Door latch striker in line with centre of
opening