manualshive.com logo in svg

Fona MyCrown Mill, Руководство по обслуживанию

Поделиться
Скачать
Fona MyCrown Mill Скачать руководство пользователя страница 97

 

97

Service Manual

båÖäáëÜ

5.1. 

Cleaning the manual block clamp

➢ Clean the inside of the block axle once a month with a round (green) 

cotton swab and undiluted ethanol (commercially available cleaning 

alcohol).

5.2. 

Milling instruments without chuck

✔

The motors are in the position for changing the milling instruments 

(burs).

1. Unscrew and remove the milling instrument.
2. Clean the inside of the clamping cone with a pointed cotton swab and 

undiluted ethanol (commercially available cleaning alcohol). When 

doing this, rotate the cotton swab counterclockwise in order to push 

the dirt out.

3. CAUTION! Do not grease the thread. Insert the milling instrument 

and screw it tight with the torque wrench.

NOTICE 

Do not grease the thread.
Do not grease the thread when using milling instruments without 

chucks.

NOTICE 

In the case of MyCrown Mill: Once a month
Clean the clamping cones of the milling instruments.

Содержание MyCrown Mill



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды