manualshive.com logo in svg

Fona MyCrown Mill, Руководство по обслуживанию

Поделиться
Скачать
Fona MyCrown Mill Скачать руководство пользователя страница 18

 

18

MyCrown Mill

2.3.2

Media supply

2.3.2.1

Media supply

Purpose of Test:

To check the media supply (air, water, fan) for proper functioning and test 

the pressure switches and the function of the pump.

Procedure

The pumps and the fan are switched on by nominal select control 

depending on selection. The motor currents and the condition of the 

pressure switches are registered. The points of time when the pressure 

detectors respond are measured. After approx. 5 seconds the pumps are 

switched off and the time required until the pressure switch responds is 

measured and evaluated.

Save

Save stores the measured values to the log file under the heading of 

Media supply.

Media supply

Deviations of measurements

Deviations may occur:

● During the first test run (if any air is still in the water circuit)
● If the amount of water in the water tank is insufficient
● After filling the water tank.

Содержание MyCrown Mill



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды