manualshive.com logo in svg

Fona MyCrown Mill, Руководство по обслуживанию

Поделиться
Скачать
Fona MyCrown Mill Скачать руководство пользователя страница 85

 

85

Service Manual

båÖäáëÜ

1. Unscrew the hose nipple with the hose (open-end wrench, 

10 mm A/F). 

2. Remove the shaft lock-down device and pull out the suction 

connection toward the front. 

3. Insert the new suction connection and fasten it with the shaft lock-

down device. 

4. Seal the thread with teflon tape and screw the suction connection 

tight again.

4.8.4

Installing the chassis insert

The installation of the chassis insert is described in the preceding chapter 

"Replacing the tank switch", see "Installing the chassis insert" [ → 83]. 

4.8.5

Final work

1. Screw on both drawers (4 screws each, using a TX 9 screwdriver).
2. Pull out the drawer on the left and on the right.
3. Reinsert the tank. 
4. Reattach all covers.

4.9. 

Replacing the light barrier

Light barrier, B axis

1. Remove the rear panel cover and the intermediate cover.
2. Unscrew the metal bracket (2 screws, TX 20 screwdriver).
3. Disconnect light barrier connector X10.
4. Pull the milling unit to the edge of the table and unscrew the defective 

light barrier from below (TX10).

5. Screw on the new light barrier.
6. Connect connector X10.
7. Screw the metal bracket back on again.
8. Reattach all covers.

G-axis and  M-axis light barriers

1. Use the service software to determine which light barrier is defective.
2. Remove all covers except for the left/right cover, depending on which 

light barrier is defective.

3. Disconnect light barrier connector X10.
4. Unscrew the defective light barrier (TX 10).
5. Screw on the new light barrier.
6. Connect connector X10.
7. Reattach all covers.

Содержание MyCrown Mill



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды