manualshive.com logo in svg

Fona MyCrown Mill, Руководство по обслуживанию

Поделиться
Скачать
Fona MyCrown Mill Скачать руководство пользователя страница 58

 

58

MyCrown Mill

4.2. 

Replacing the (DC) spindle motors

4.2.1

DC motor, single

4.2.1.1

Removal

Preparation

1. Switch the milling unit on.

The motors move into the home position.

2. Switch the milling unit off at the main switch (0).
3. Open the milling chamber door.

Removing the motor unit

1. Remove the fastening screws of the mount cover.
2. Remove the fastening screws of the shaft.
3. Pull the motor mount together with the motor off of the shaft and the 

mount cover. At the same time, unplug the power supply connectors.

Removing the motor

1. Remove the fastening screws of the motor.
2. Pull the motor out of the motor mount.
3. If necessary, pull the plug connector strip out of the motor socket and 

connect it to the socket in the milling unit.

A

Mount cover

D

Fastening screws, motor 

mount/mount cover

B

Motor mount

E

Fastening screws, shaft

C

Fastening screws, motor

E

D

C

B

A

Содержание MyCrown Mill



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды