Festo CPX-FB23 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 122

background image

2. Commissioning

2−41

Festo P.BE−CPX−FB23−EN en 0308NH

2.3.3

RAS function

The CPX terminal supports the RAS functions (Reliability,
Availability, Serviceability) of the field bus CC−Link.

Functions for separating slave stations:

Even if a decentral or local station fails (e.g. voltage
drop), network operation will not be impaired.

A  defective  slave  station  can  be  replaced  whilst  the  net
work  is  in  operation  (the  voltage  of  the  station  to  be  re
placed  must  be  switched  off ).

When  a  station  is  linked  into  the  system  again  after  a  fault
has  been  eliminated,  it  is  not  necessary  to  reset  the
master  station.

Monitoring the communication status:

The network can be monitored by the master station dur
ing system set−up, during debugging or during mainten
ance.

«
...
83
84
85
86
87
...
»

Содержание CPX-FB23



























































































































Отзывы:

Нет отзывов

Похожие инструкции для CPX-FB23

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 8

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

ECL Comfort 210

Бренд: Danfoss Страницы: 12

ECL Comfort 110

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 64

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: GI.BI.DI Страницы: 60

DuoControl Signal 111

Бренд: Tormatic Страницы: 3

Бренд: Netro Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды