Festo CPX-FB23 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 122

background image

1. Installation

1−9

Festo P.BE−CPX−FB23−EN en 0308NH

Setting the operating mode

1

You can set the operating mode of the CPX terminal with
switch element 1 of the 2−element DIL switch 1:

Operating mode

Setting DIL switch 1.1

Operating mode Remote I/O

All  functions  of  the  CPX  terminal  are
controlled  directly  by  the  higher−
order  PLC/IPC.  An  FEC  integrated  in
the  CPX  terminal  functions  as  a
passive  function  module  without
controller.

1.1: OFF
(factory setting)

Reserved for future extensions:

Operating mode Remote Controller

An  FEC  integrated  in  the  CPX  ter
minal  takes  over  control  of  the  I/Os.
Thi  soperating  mode  is  useful  if  an
FEC  is  integrated  in  the  CPX  ter
minal.

1.1: ON

Tab.1/1:

Operating mode

Please note

The setting of the operating mode with the DIL switch has
priority over all other settings.

«
...
21
22
23
24
25
...
»

Содержание CPX-FB23



























































































































Отзывы:

Нет отзывов

Похожие инструкции для CPX-FB23

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренд: Vacon Страницы: 30

Бренд: Vacon Страницы: 81

Бренд: Vacon Страницы: 100

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Бренд: DSEGenset Страницы: 74

Бренд: ITALFARAD Страницы: 32

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды