Ferrari 458 Spider Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 260

background image

208

Advice for Emergency Situations

Replacing a wheel

Important note

If one or more wheels need to be replaced, proceed as follows:
• replace the wheel stud bolts with damaged threads or tapers
• carefully clean the wheel stud bolts before ﬁtting
• do not lubricate the contact surfaces between the stud bolt

and the wheel rim and between the wheel rim and the brake

disk.

In order not to remove the antilock coating, do not clean the

wheel rim cones with solvents or aggressive products.

Collapsible spare wheel (optional)

On request, the vehicle comes with a kit containing:
• collapsible spare wheel

A

with space-saving tyre; label

B

indicates

the maximum speed allowed of 80 km/h (50 mph);

• additional tool bag

C

containing the jack for raising the vehicle

and the socket wrenches for operating the jack and tightening the

wheel stud bolts.

Warning

The spare wheel must only be used for short trips in the event

of an emergency.
When the spare wheel is ﬁtted, never exceed the maximum

speed of 80 km/h (50 mph) and drive carefully, especially

around bends and when overtaking, avoiding sudden

acceleration or braking.
Do not exceed the approved weight limits.
Do not ﬁt snow chains on the spare wheel.
Never ﬁt more than one spare wheel at a time.

Important note

Failure to comply with these instructions could lead to loss of

control of the vehicle and consequently damage to the vehicle

and injuries to its occupants.

�

�

�

«
...
206
207
208
209
210
...
»

Содержание 458 Spider





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 458 Spider

Бренд: Conrad Страницы: 26

2003 Thunderbird

Бренд: Ford Страницы: 200

Бренд: Whispbar Страницы: 15

Бренд: Cadillac Страницы: 518

Бренд: Opel Страницы: 141

Бренд: Nav TV Страницы: 2

Бренд: ULTIMATE SPEED Страницы: 21

StreetLine Series

Бренд: SAAS Страницы: 4

2011 A3 Sportback

Бренд: Audi Страницы: 29

Бренд: Yakima Страницы: 12

Бренд: Axxess Страницы: 16

Бренд: RHOX Страницы: 8

Бренд: E&G Classics Страницы: 4

Бренд: Gator Страницы: 6

Бренд: PUTCO Страницы: 2

Бренд: Subaru Страницы: 2

Бренд: Belkin Страницы: 30

Бренд: Mitsubishi Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды