Ferrari 458 Spider Скачать руководство пользователя страница 113

Страница: 113 / 260

113

About your Vehicle

Fault display

Fault displaying logic

When a fault occurs, the corresponding warning light (if present)

comes on on the panel whereas a description of the fault (if

available) and the relevant symbol (if available) are displayed on

the left TFT display. The message appears on the display at the

same time as the warning light (if present) comes on and the main

screen page that is displayed at that moment is minimised.
The fault remains on the display for 20 seconds. When the display

cycle ends, if the fault does not have a special warning light on the

panel, the symbol remains minimised in area

of the display (see

page 97) until the cause of malfunctioning has been resolved. In

area

the main screen page is displayed in “maximum” size.

When the display cycle ends, if the fault has a special warning

light on the panel, the screen page that was displayed prior to the

event reappears and the symbol is not minimised in area

. The

warning light remains on until the cause of malfunctioning has

been resolved.

If the fault is resolved within 20 seconds, it remains displayed and

the warning light remains lit for 2 seconds.

“ESCAPE” function

Displaying a fault on the screen can be interrupted by pressing and

quickly releasing the

button with “ESCAPE” function. When

the

button is pressed, the screen page that was displayed prior

to the event reappears. If the fault does not have a special warning

light on the panel, the symbol remains minimised in area

until

the cause of malfunctioning has been resolved.

Catalysts temp.

too high

Engine

performance

limited

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды