Ferrari 458 Spider Скачать руководство пользователя страница 149

Страница: 149 / 260

149

About your Vehicle

“Automatic gearbox” mode

The “Automatic gearbox” mode is enabled/disabled by pressing the

AUTO

button on the centre console. When the “Automatic” mode

is enabled, the word “auto” appears on the gearbox display. To exit

the “Automatic” mode, you must press the

AUTO

button until the

word “auto” on the gearbox display disappears.
When the “Automatic Gearbox” mode is enabled, the system will

automatically UP-shift and DOWN-shift according to vehicle speed,

engine revs and the torque/power request of the driver.
When you are in “Automatic” mode, you can however manually

shift gears using the

and

DOWN

paddles. The system remains

in “Automatic” mode: this is indicated by the word “auto” that

remains on the gearbox display in ﬂashing mode when the paddles

are used.
When the vehicle is stationary, a “

”,

gear or “

”request will not

result in a change from “Automatic” to “Manual”.

“Auto easy exit” mode

Every time the vehicle is started, the gearbox starts in “Auto easy

exit” mode unless it was in “Automatic” mode when the engine was

turned off. In this case, it remains in “Automatic” mode the next

time the engine is started.
Activation is signalled by the word “auto” and an arrow in the

gearbox display.
In this mode, the system will automatically UP-shift and DOWN-

shift according to vehicle speed, engine revs and the torque/power

request of the driver.
To exit the “Auto easy exit” mode and go to “Manual” mode,

operate the

DOWN

paddle (while the vehicle is moving) or

press the

AUTO

button on the centre console.

If the “Automatic” gearbox mode is then requested by pressing the

AUTO

button, the system will apply all the characteristics of the

“Automatic” gearbox mode.

Push start

Warning

Push starting is not allowed.

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды