Ferrari 458 Spider Скачать руководство пользователя страница 171

Страница: 171 / 260

171

About your Vehicle

Information on automatic restarting of engine

With the Stop&Start system activated in a stopped vehicle

condition, the driver can restart the engine by:
- releasing the brake pedal
-

-shifting

- engaging reverse gear
- pressing the accelerator pedal

Warning

If the engine is switched off accidentally and not by the

Stop&Start system, it must be restarted manually by the driver

by pressing the

ENGINE START

button and reengaging the gear

using the shift paddles located behind the steering wheel. This

condition is indicated on the left TFT display by the message

“Press ENGINE START button to restart”, accompanied by an

acoustic signal.

For safety reasons and to guarantee comfort when the vehicle

is stationary and correct operating of the entire vehicle, the

Stop&Start system also automatically restarts the engine when:
- the

ENGINE START

button on the steering wheel has been pressed

- the function has been deactivated by pressing the button located

on the roof panel

- the driver’s seat belt has been unfastened
- the driver-side door has been opened
- the hard top is being opened or closed
- the Front Lift system has been activated
- rear screen demisting has been requested or the air conditioning

and heating system set to “low” or “max defrost”.

The system also constantly monitors some of the vehicle operating

parameters (battery charge level, engine coolant temperature,

catalytic converter temperature, clutch oil temperature, vacuum

level in brake servo, climate comfort in passenger compartment,

vehicle speed) so that the engine can be automatically started in

certain conditions to guarantee safety and vehicle operating and

minimise the impact on on-board climate comfort.

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды