Ferrari 458 Spider Скачать руководство пользователя страница 118

Страница: 118 / 260

118

About your Vehicle

orange orange

ABS

Indicates an ABS system failure (priority level

The standard braking system is still functioning.

Contact the F

errari Service Network.

orange orange

ESC off

Symbol and warning light indicate that the ESC

system has been deactivated (priority level

The symbol is displayed for 5 seconds together with

the “ESC off” message.

orange orange

ESC system failure

Indicates a fault in the ESC system (priority level

Warning

Stop the vehicle and avoid sharp braking.

Stop driving and contact the

Ferrari Service

Network

immediately.

Warning

However, the vehicle can be moved to clear

the road by adjusting the speed to the road

conditions and type of road.

orange

ESC system activation (ﬂashing warning light)

Indicates that the ESC system has been activated

(priority level

green

Hazard warning lights

The left and right hand turn indicator lights ﬂash

simultaneously if the hazard warning lights are

activated.

red

Catalytic converter temperature

Indicates that the catalytic converter temperature is

too high: stop the vehicle (priority level

Contact the

Ferrari Service Network

orange

Indicates that the catalytic converter temperature is

very high: reduce speed until the symbol goes out

(priority level

Indicates a failure of the catalytic converter

temperature sensor (priority level

orange

Checking the engine oil level

Indicates a low engine oil level (priority level

orange

Seat heating

Indicates that heated seat function is enabled

(remains displayed for 5 seconds).

orange

Power steering failure

Indicates that the power steering system is

inefﬁcient (priority level

Contact the

Ferrari Service Network

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды