Ferrari 458 Spider Скачать руководство пользователя страница 127

Страница: 127 / 260

127

About your Vehicle

SPORT mode

This is the ideal setting for vehicle performance recommended for

everyday driving in medium- to high-grip conditions.

RACE mode

This mode offers maximum performance and stability in high grip

conditions and is particularly suitable when using the vehicle on

track.

CT OFF mode

When this mode is selected, the F1-Trac traction control system is

disabled whereas stability control remains active. This mode is used

on the race track in high grip conditions.

ESC OFF mode

This mode allows the driver complete freedom and control of the

vehicle for track use in high-grip conditions.
No electronic system other than the E-Diff controls vehicle stability.

Warning

In low- to medium-grip conditions (e.g. wet, icy, sandy roads),

do not deactivate the

ESC

system.

Important note

For further information on the driving modes that can be

selected, refer to the paragraph “Driving using the driving mode

control switch” on page 155.

“Manettino” driving mode control switch

The driver can select the desired driving mode by using the

“Manettino”

The driving mode selected does not exempt the driver from

complying with the rules of safe driving.

Important note

In the event of a failure of one of the onboard systems, signalled

by the special symbol on the left TFT display, the Manettino”

moves to a “recovery” position, but still allows the vehicle to be

driven. In these cases, contact the

Ferrari Service Network

Driving modes that can be selected with “Manettino”

WET mode

This is the maximum safety driving mode. Recommended in low

grip conditions.

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды