Ferrari 458 Spider Скачать руководство пользователя страница 216

Страница: 216 / 260

216

Advice for Emergency Situations

After connecting the battery conditioner to the socket in the

vehicle, run the connection cable under the passenger door on the

front side.

Important note

Do not run the connection cable out of the vehicle in positions

other than those indicated to prevent damaging the seals and/or

the cable.

If you do not plan to use the vehicle for over a week, we

recommend you connect the battery conditioner to keep the battery

in perfect working order.

Warning

The engine cannot be started as long as the battery conditioner

is connected to the vehicle socket.

Battery conditioner

The vehicle is equipped with a battery conditioner to maintain and

recharge the battery.

Important note

Using the battery conditioner will extend the life of the battery.

The device is kept in a pocket inside the car cover bag supplied

with the vehicle.
The battery conditioner connection socket

is located under the

dashboard on the passenger side.

Warning

Place the battery conditioner where it can be easily seen away

from heat sources and out of children's reach.

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды