Ferrari 458 Spider Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 260

background image

48

Quick reference guide

If the engine fails to start after several attempts, check for one of

the following causes:
• insufﬁcient speed of the starter motor (ﬂat battery)
• ignition device faulty
• electrical contacts faulty
• fuel pump fuses blown.

Warming up the engine

Do not run the engine at high speed until the engine oil temperature

has reached at least 65-70 °C (149-158 °F), approximately.

Starting the vehicle

With the engine started, the vehicle stationary and the brake pedal

pressed, pull the right-hand “

UP

”

paddle towards the steering

wheel to engage

1

st

gear.

Release the brake pedal and press the accelerator to start off.
With the engine running and the vehicle stationary, you can change

directly from

1

st

or

2

nd

gear to

R

(reverse) by pressing

R

and from

reverse to

1

st

by moving the

UP

paddle.

Warning

If the “

UP

” and “

DOWN

” paddles are not working, the message

“Depress brake pedal and press LAUNCH to engage gear” will

appear on the left TFT display; you can therefore engage the

gear by pressing the

LAUNCH

button on the centre console (see

page 164) and the brake pedal.
In these cases, the “Launch Control” function is not available.
If the engaged gear was

R

, the

LAUNCH

button must be pressed

twice to engage

1

st

gear.

Important note

When reverse is selected, an acoustic safety signal beeps

intermittently as long as “R” is engaged.

If the system automatically selects

2

nd

gear when attempting to

shift from

R

to

1

st

gear, this indicates that

1

st

gear has jammed.

Therefore, this is not a malfunction, as it falls within the system

operating logic. For the same reason, when shifting from

1

st

gear

to “

R

”, the system will automatically engage “

N

” if the gear has

jammed.
During prolonged stops with the engine running, it is advisable to

keep the gearshift in

“

N

”.

Important note

If you allow the vehicle to move forward in N, when UP or

DOWN is requested, a gear will be engaged that corresponds to

the speed of the vehicle.

R

«
...
46
47
48
49
50
...
»

Содержание 458 Spider





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 458 Spider

Green Motion DC 22

Бренд: Eaton Страницы: 65

Бренд: Ford Страницы: 22

Бренд: Yakima Страницы: 13

Бренд: Menabo Страницы: 11

Vantage 12 Series

Бренд: Ecco Страницы: 5

Бренд: Sears Страницы: 41

Бренд: Whelen Engineering Company Страницы: 9

BEDXTENDER HD MAX 74841-00A

Бренд: AMP Research Страницы: 9

Бренд: Belkin Страницы: 2

Alloy Rugged Ridge X-Clamp

Бренд: Omix-Ada Страницы: 2

Бренд: Dodge Страницы: 3

Бренд: Havis Страницы: 5

Бренд: BMW Страницы: 392

Бренд: Curt Manufacturing Страницы: 4

Prime Design VBI-FT31B

Бренд: Safe Fleet Страницы: 12

Бренд: Saab Страницы: 288

Бренд: Sintrones Страницы: 55

Бренд: Kuda Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды