Ferrari 458 Spider Скачать руководство пользователя страница 166

Страница: 166 / 260

166

About your Vehicle

Front Lift

If the engine is turned off with the front suspension lift activated,

the message “Front Lift ON. Set Front Lift to OFF” appears on the

left TFT display at key-off. Turn the key back to position

(key-

on) and press button

to lower the vehicle. If it is not manually

deactivated by pressing the button, within 15 seconds of turning off

the engine, the system is automatically deactivated.

Warning

The system has not been designed to remain activated when

the engine is turned off and the vehicle is stationary. If the

engine is turned off with the front lift activated, the vehicle is

automatically lowered after 15 seconds.
Do not use the front suspension lift to park the vehicle on

obstacles (e.g. pavements); these obstacles may come into

contact with the front of the vehicle and damage it once the

system has been deactivated.

In the event of engine failure, the “Front Lift” system can however

be activated by pressing button

for 10 seconds. In this way, the

vehicle front can be lifted even in emergencies when the engine is

turned off (for example, to load it onto the ramp of a breakdown

vehicle).

Important note

The front suspension lift should only be used for the purposes

described above and not to drive over speed control systems (e.g.

traffic calmers) more quickly.

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды