Ferrari 458 Spider Скачать руководство пользователя страница 76

Страница: 76 / 260

Safety

Tyre temperature and pressure monitoring
system ( TPMS) (optional)

On request, the vehicle can be equipped with a system that

measures the tyre pressure and temperature using special sensors

ﬁ tted inside the wheel rims next to the air valve. These sensors

transmit a signal that is received by the antennas on the car body,

behind the gravel guards, that are connected to the ECU.

Important note

The system may be momentarily affected by radioelectrical

interference from devices that use similar wavelengths.

The ECU processes this information and transmits data on tyre

pressure and temperature and any system errors to the instrument

panel.
The signal transmitted by the ECU activates symbols on the left

TFT display (see page 96) with two priority levels: a

soft warning

(SW) if the pressure loss is

0.2 bar more

than the rated pressure

and a

hard warning

(HW) if it

is 0.5 bar more

or there is a

dynamic decrease of over 0.2 bar/min.
The TPMS can be calibrated using the special menu item in the left

TFT display (see page 98).

Important note

System calibration using the special menu item on the left TFT

display is necessary after replacement or inﬂ ation of a tyre or

tyres.

Warning

The TPMS warns the driver that the tyre pressure has

decreased. However, this does NOT exempt the driver from

periodically checking that the tyres are inﬂ ated to the indicated

pressure.
In addition, the system does NOT warn the driver of damage to

the tyres by external agents.

Displaying messages on the left TFT display

By using the commands on the left TFT display (see page 96), the

driver can access the TYRES screen page which displays the vehicle

symbol with the pressure and temperature values of each tyre as

shown in example

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды