Ferrari 458 Spider Скачать руководство пользователя страница 237

Страница: 237 / 260

237

Care of the vehicle

Maintenance of seat belts and pretensioners

• Periodically check that the screws on the anchor points are tight

and that the seat belt is in perfect condition and slides smoothly.

• The seat belt must be kept clean; the presence of any dirt could

prevent the seat belt retractor from working properly.

• To clean the seat belt, wash it by hand with mild soap and water,

rinse it and let it dry. Do not use strong detergents, bleach or

aggressive solvents, as they can weaken the ﬁbres.

• Do not let the seat belt retractors get wet: proper functioning is

only ensured if they are kept dry.

• The pretensioner requires no maintenance or lubrication. If

immersed in water or mud, the pretensioner must necessarily be

replaced.

• The pretensioner must be replaced at the intervals indicated in

the “Warranty Booklet”.

Cleaning the vehicle

Cleaning the exterior

Environment

All the materials used for the following operations (e.g. cloths

soaked with oil or grease, pans, etc.) must be disposed of in

compliance with the environmental protection regulations.

Proper care of the vehicle on the part of the owner is essential for

the vehicle long life.
Here is a list of the main precautions to be taken.
• Certain parts of the vehicle should not be left wet or dirty for

long periods of time: in particular, the passenger compartment

ﬂoor and the luggage compartment must always be kept clean and

dry. The drain holes under the doors should be kept unclogged to

allow any water to drain.

• The underbody and the lower surfaces of the vehicle should be

cleaned regularly, and more frequently (at least once a week) if

the vehicle is used on salty or rough roads. The vehicle should

be cleaned thoroughly and carefully: cleaning that merely

wets encrusted mud without removing it completely can prove

damaging.

• The vehicle must be washed regularly with suitable equipment.

Do not use very hot water or steam to clean the paintwork and

the lower surfaces. It is advisable to soften any dirt ﬁrst, then

remove it with a jet of water at room temperature.

Содержание 458 Spider





































































































































































































































































Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды

Ferrari 458 Spider, Руководство пользователя

Результаты поиска

Содержание 458 Spider

Отзывы:

Похожие инструкции для 458 Spider

Бренды по названию

Популярные бренды