FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 45

Страница: 45 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

ROOF/SIDEW

ALL

FRAME DIAGRAM - 104713

iew shows the

outside

surface of the roof and sidewall.

ATTENTION:

Numbers in ( ) are stamped on the part.

Gutter Rail

(32-8)

Sidewall Diagonal Struts (33)

Roof Diagonal Strut (95)

Double

Track

Support Rafter (52)

Ridge Beam (50)

Base Rail (30-8)

Rafter (51)

Double

Track

Side Support

(14)

SPECIAL

NOTE:

During assembly

, the

double track of the support (52) must face toward the non-door end wall to allow for the installation of the single-bay vent frame.

Non-Door End W

all

R = Long bolt with a red head.

All bolts with a painted

red head are used exclusively to attach all sidewall struts to the sidewall frames. Positions of these bolts are identified by the letter R in the diagram.

This frame

uses six (6) long bolts to secure the sidewall struts.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды