FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 8

Страница: 8 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

5. Locate the remaining angled bracket and attach it to

the end of the upper support.

Do not tighten bolts at

this time.

ASSEMBLE THE END WALL FRAMES (CONTINUED)

ATTENTION:

Some upper supports may include a

bolt track

instead of the pre-drilled holes

as shown in

the photo. If so, slide bolts into the track and attach

bracket.

6. Select the short, lower support, slide two bolts into the

bolt track, and attach the lower support to the angled

bracket as shown below.

7. Attach the lower support to the angled bracket using

nuts and the bolts in the track. Insert bolts through

drilled holes of the bracket.

Do not tighten bolts at this

time.

Upper Support (15)

Lower Support (14)

Slide

bolt head

through here.

Lower Support (14)

Upper Support (15)

Attach Strut Here

8. Verify that the four bolts are loose and place the

template into position as shown in the photos below.

ATTENTION:

The template is used to set the proper

clearance for the gutter rail. The template slides into

the slots in each frame member.

9. With the template in position, tighten the upper bolts to

secure the bracket to the

upper frame member (15)

the end wall. See the arrows above.

Template

template

REMINDER:

Brackets are installed on the inside of the

shelter.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды