FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 10

Страница: 10 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

ASSEMBLE THE END WALL FRAMES (CONTINUED)

14. Take the longer (12-2) support and the two brackets

(110 & 65-1). Insert the top bolt of the 12-2 support

through the pre-drilled hole in the upper support. Insert

the next 3 bolts into the pre-drilled holes of the 110

bracket. Position the angle of the bracket along the

lower edge of 12-2 support. See photo below.

Brackets

110

65-1

110

65-1

12-2

15. Select the next bolt in the 12-2 support and insert the

bolt into the pre-drilled hole of the 65-1 rectangular

bracket. Insert the remaining two (2) bolts in the header

(65) track into the remaining holes of the 65-1 bracket.

Align Bracket 65-1 with the edge of the 110 bracket.

To this point the end frame should resemble the photo

below.

Bolt

12-1

Horizontal Brace

16. Locate a remaining bolt in the bolt track of the short

12-1 support and attach one horizontal brace (19) to

the bolt.

Do not tighten the bolt at this time.

17. Move to the angled bracket (18) and attach the brace

using the bolt as shown.

18. Repeat steps to attach the remaining horizontal

brace (19) to the 12-2 support and the 14A end frame

support.

12-2

14A

Upper Support

(15)

Diagonal Strut

Base Rail Location

19. Attach the remaining diagonal strut (19).

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды