FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 21

Страница: 21 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

Picture shows the location of cross members.

The greenhouse model may differ.

9. Install the two (2) cross members (75) between the

three rafters where the vent frame will be installed.

ASSEMBLE AND INSTALL THE ROOF VENTS

(CONTINUED)

NOTE:

View shows the frame as seen when standing

on the inside. Only one (1) cross member (75) is shown

in the above photo.

10. Using the additional bolts (rafter assembly) in the bolt

tracks, attach the cross members (dashed line below)

between the rafters.

Do not tighten the bolts at this

time

Double-bay vent position shown for 104713.

NOTE:

The X's in the above photo show where to

attach the Z-brackets (77). The Z-bracket holds the

vent support arms in place when the vent is closed.

Single-bay vents have a single Z-bracket; each double-

bay vent has two (2) Z-brackets–one for each support

arm.

Photo below shows one end of the cross member (75)

where it is attached to the rafter. The bolt is on the

underside of the rafter, which is to the inside of the

greenhouse.

To the ridge

beam

View shows the cross member (75)

from the outside

11. After attaching the cross members (75), take the

assembled vent frame and insert one end into the

C-channel of the ridge beam. See the photos below

and vent frame diagram for details.

12. Slide the vent frame into the channel.

The side of the

vent frame that was facing up during its assembly

should now be facing to the inside of the frame.

ATTENTION:

You must flip the assembled vent frame

over so that the rounded edge of the top hinge rail can

be inserted into the channel of the ridge beam.

Cross

Member (75)

Rafters

(51)

Sidewall Supports (31)

Gutter Rail

Ridge Beam

Top of

Hinge Rail

Ridge Beam

Top Hinge Rail

of Vent Frame

ATTENTION:

Ridge beam design

may differ from

actual beam. Vent

installation is the

same.

Inset shows the ridge beam of a

home-attached greenhouse.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды