manualshive.com logo in svg

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Поделиться
Скачать
FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 30

GROWSPAN

™

 ESTATE ELITE ATTACHED GREENHOUSES

30

Revision date: 01.01.16

3.  Take one section of the U530 profile and install it on the 

top edge of the polycarbonate panel. 

NOTE: 

The top and bottom edges of each panel show 

the hollow cells inside the panel. When installing the 

plastic molding, rest the panel on cardboard or other 

material to protect the edges and surface of the panel.

Polycarbonate Panel

Plastic U-strip (U530)

4.  Take another section of the U530 profile and attach it to 

the bottom edge of the panel.

INSTALL THE POLYCARBONATE DOOR PANELS 

(CONTINUED)

6.  Mark the UV-protected side with a piece of tape or a 

marker and remember that it is installed to the outside.

7.  Lift each door frame off the hinges and place the 

frames (inside surface down) on cardboard to protect 

the door frame finish. 

Photo shows the lower corner of one door frame. 

Dashed lines show where to apply silicone.

8.  Verify that the assembled panels fit into the door frame.
9.  Apply a bead of silicone around the door frame as 

shown where the panel is positioned.

10. Place a prepared panel into the door opening. Verify 

that the 

UV-protected surface is to the outside

.

11.  Repeat the previous steps to attach the remaining 

polycarbonate panel to the remaining door frame.

12. After the silicone sets, the doors can be place back on 

the hinges, or you can wait until all remaining panels 

are installed on the greenhouse frame. This will help 

prevent damage to the door panels during the final 

stages of assembly.

13. Continue with installing the ends for the gutters.

Cells

5.  With both lengths of the plastic U-strip installed on the 

panel, peal the protective film from the panel.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды