FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 11

Страница: 11 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

ASSEMBLE THE END WALL FRAMES (CONTINUED)

Vertical Support

To the top of the

end wall frame.

Base Rail (10)

Up to this point, all end wall frame members are

attached except for the base rail. The dotted line shows

the position of the base rail. See photo below.

20. With the end wall assembled as shown, locate the base

rail (10) and position it at the ends of the lower supports

and vertical supports.

14A

NOTE:

The slot used to attach the base rail to

the lower support is positioned to the inside of the

greenhouse. The view above is an end view of the

base rail. Actual rail may differ slightly in design.

21. With the base rail in position, insert the bolt of one (1)

door support

through the pre-drilled hole in the base

rail and hold the bolt in place.

Do not install the nut on

the bolt at this time

22. Take the free end of the diagonal strut and insert the

bolt of the door support through the pre-drilled hole in

the diagonal strut and install the nut.

ATTENTION:

Verify that the bottom of the door support

is tightly seated against the top of the base rail

before

you tighten the bolt and nut.

View is from the outside of the greenhouse looking

at the top of the base rail where the door support is

attached.

23. With the support tight against the top of the base rail,

tighten the nut and repeat the steps to attach the

remaining door support and diagonal strut to the end

wall base rail.

24. After attaching both struts and door supports to the

base rail, move to one end of the base rail and attach

the lower end of the vertical support.

Vertical Support

14A

Base Rail (10)

Vertical Support

14A

Base Rail (10)

Notch toward the inside

of the greenhouse.

Flush to the top

of the base rail.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды