FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 23

Страница: 23 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

INSTALL THE POLYCARBONATE VENT PANELS

The steps below describe attaching the polycarbonate

vent panels to the assembled vent frames. The panels are

lettered for identification. Consult the panel diagrams and

the diagrams on the outside of each shipped box to locate

and identify parts.

See Page 32 for additional information.

The parts needed to complete the vent frame assembly

include the following:
• Polycarbonate Panels: Letter X
• U602 U-profile and silicone

2. Carefully peal the protective film away

from the edge

on both sides of the panel if needed.

To prevent scratching the panel,

do not

completely

remove the protective film until the plastic U-strips are

installed.

3. Take one U-strip and install it on the top edge of the

polycarbonate panel.

NOTE:

The top and bottom edges of each panel show

the hollow cells inside the panel. When installing the

plastic molding, rest the panel on cardboard or other

material to protect the edges and surface of the panel.

4. Take the remaining strip and attach it to the bottom

edge of the panel.

Plastic U-Strip

Polycarbonate Panel

Photo shows a single panel. Panel cells run vertically

and are "capped" by the U-strips.

5. With both U-strips installed on the panel, remove the

remainder of the protective film.

6. Mark the UV-protected side with a piece of tape or a

marker and verify that the panel fits the vent frame.

Adjust frame as needed. Set panel aside.

Plastic U-Profile

Install this

edge toward

the UV-

protected side

of the panel.

Install this

edge on the

backside of

the panel.

NOTE:

The plastic U-strips are precut and are as long as

the polycarbonate panel is wide.

You do not have to cut any

plastic molding.

If it appears as though the plastic profile

is the incorrect length, verify that you have selected the

correct panel and profile.

Consult the panel diagrams near

the back of these instructions for details.

Do not allow panels to remain in direct sunlight with the

protective film intact.

Complete these steps:

ATTENTION:

Install the polycarbonate panels with the

UV-protected side to the

outside of the greenhouse

. If you

remove the protective film before installing the panels, mark

the panel in a lower corner to identify the UV-protected

side.
1. Locate the first X panel and the plastic U-strips for that

panel.

Greenhouse Sku Number

Panels/U602 in boxes:

104711 – 104713 – 104715

No. 4-4

Cells

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды