FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 33

Страница: 33 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

Polycarbonate Panel

U-Profile

4. Take another section of u602 U-profile and attach it to

the bottom edge of the panel.

INSTALL SIDE PANELS (CONTINUED)

Photo is used to illustrate the location of the U-profile.

The panel size may differ from the actual panel.

5. Move to the frame where the panel will be installed and

clean the surfaces where the silicone will be applied.

NOTE:

The surface for the silicone on the frame must

be free of oil and dirt for best results. See the profile

and panel diagrams and photo to the right for silicone

location.

6. With the plastic U-strip installed and the surface

cleaned, dry fit the panel to verify that it fits between

the frame members.

7. Remove the protective film from the panel and mark

the UV-protected side with a piece of tape or a marker

and set the panel aside.

8. Move to the frame and, standing outside the frame,

apply a bead of silicone

in the channel of each frame

member

in the areas shown below by the dashed lines.

ATTENTION:

Panel is shown in place to better show

the location of the silicone, which is applied

before

the

panel is set in the frame.

9. After the silicone is applied, take the prepared panel

and set the panel into position as shown above.

Panel

as seen from the outside.

NOTE:

Protective film has be left in place to better

show the panel.

10. Firmly press the panel against the silicone on the rafter.

Panel will sit between the frame members.

11. Continue by installing the metal clips to secure the

panel to the frame.

Silicone is between

the backside of the

panel and the frame

members.

U-Profile

Dashed line

shows where to

apply silicone

before installing

the panel.

View is from the

outside of the

greenhouse.

Cells

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды