FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 18

Страница: 18 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

4. Install the corner bracket (94). After installing all bolts,

tighten all nuts.

NOTE:

Photo above shows the 104715 frame that

includes a 2-piece gutter rail. The 104711 and 104713

do not include the additional gutter rail brackets.

5. Attach the upper bracket (101) to the support (52).

(Actual number of bolts for brackets may differ from

what is shown in these photos.)

Do not tighten bolts.

6. Using four (4) bolts in the double track sidewall support

(14), attach the lower bracket (100).

Do not tighten.

INSTALL THE ROOF RAFTERS (CONTINUED)

7. Attach the diagonal brace (102) to the support brackets

(100 and 101).

Tighten bolts.

8. Once the diagonal brace (102) is in place, tighten all

nuts and bolts on brackets.

9. Using the remaining bolt in the track of sidewall support

(14), attach the horizontal brace (103). Do not tighten;

allow brace to freely move along vertical.

NOTE:

Frame shown may differ slightly from actual

frame; assembly is the same.

10. Secure the remaining end of the horizontal brace (103)

to the diagonal brace (102).

11. Verify that the 103 brace is level and tighten the bolts.

Horizontal

Brace (103)

Sidewall Support

(14)

Diagonal

Brace (102)

Lower Support

Bracket (100)

Sidewall

Base Rail

Upper Support

Bracket (101)

101

Upper Bracket

Lower Bracket

Diagonal

Brace

Diagonal

Brace

100

102

101

Gutter Rail

ATTENTION: Verify that you have one additional

bolt remaining in the track of the sidewall support

(14) to attach the 103 brace. See Step 9 in the next

column. Remove bracket and add a bolt if needed.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды