FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 13

Страница: 13 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

3. Attach each vertical support (31) to

the gutter rail

inserting the bolt through the pre-drilled hole in the

gutter rail.

Do not tighten at this time.

ATTENTION:

For the sidewall support (14) with two

bolt tracks, the gutter rail (and base rail) will seat into

the slot of the support. Insert the bolt through the pre-

drilled hole in the frame member. Do not tighten.

Photo shows the double-bolt track support (14) with

the base rail seated into its slot. Top of the support is

attached to the gutter rail in a similar fashion.

NOTE:

The slotted hole at

each end of the gutter rail

is used to attach the end wall frame assembly to the

sidewall. Use the diagram to position the first vertical

support (31) in the correct location.

The photo above shows the vertical support (31) and

diagonal strut (33) as

attached to the gutter rail

of the

sidewall. View shows the inside of the frame.

SIDEWALL ASSEMBLY (CONTINUED)

Gutter Rail

NOTE:

Pictures may not reflect actual length. Consult

the Roof/Sidewall Frame diagrams near the end of

these documents for each length layout.

5. Attach the struts (33) to the gutter rail as shown below.

Do not fully tighten the bolts at this time

4. Insert the remaining bolts, located in the bolt tracks of

the vertical supports (31), into the pre-drilled holes of

the base rail. Remember to attach diagonals where

applicable.

6. Once all vertical supports are attached to the gutter rail

and the base rail, tighten all bolts. Use a carpenter's

square or similar tool to square the frame as bolts are

tightened.

Slot is next

to bolt track

identified by X.

Applies to

104713 and

104715

frames only.

7. After the final sidewall is assembled, continue with the

frame assembly procedure that follows.

Use red-headed

bolts to attach

struts.

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Estate Elite 104711

Бренды по названию

Популярные бренды