FarmTek Growers Supply GrowSpan Estate Elite 104711 Скачать руководство пользователя страница 34

Страница: 34 / 55

GROWSPAN

™

ESTATE ELITE ATTACHED GREENHOUSES

Revision date: 01.01.16

INSTALL THE END WALL PANELS

The end panels are installed and secured in the same

manner as the sidewall panels: The U-strip is installed at

the top and bottom; the retention clips are installed along

each side. Only the panel shape differs.

NOTE:

All end panels are cut to the proper size. You do not

have to cut any polycarbonate panels.

For the door end of the greenhouse, locate these panels:
•  One (1) large, angled panels: Panel A1
•  One (1) large, angled panels: Panel B1
•  One (1) small angled panels: Panel C1 (Install this

panel above the door opening).

For the non-door end of the greenhouse, locate these

panels:
•  One (1) large, angled panels: Panel A2
•  One (1) large, angled panels: Panel B2
•  One (1) center, angled panels: Panel C2

NOTE:

When installing the panels,

install the UV-

protected side to the outside

of the greenhouse.

Panel Locations: Door End Frame (inside view)

INSTALL METAL RETENTION CLIPS

There are two sizes of wire clips used to secure the panels

to the frame (82 and 87). Consult the

Panel, Profile, and

Spring Location Diagrams

near the back of this guide for

spring clip installation locations.

Continue with the following steps to install the clips on the

outside of the greenhouse

1. With the panel in place, take a wire clip and place it

against the sidewall vertical support and panel.

2. Clip the free ends

of the wire spring

behind the lip of the

frame member and

press into place.

CAUTION:

Wear

eye protection when

installing and working

with the wire clips.

Place wire clip into

position as shown.

Use a pliers if needed

to clip the spring in

place.

Panel

NOTE:

Refer to the diagram for the correct wire spring

size and to properly space the wire clips.

3. Repeat steps to install and secure all sidewall panels,

then install the end panels and roof panels.

Panel Locations: Non-Door End Frame (inside view)

Содержание Growers Supply GrowSpan Estate Elite 104711
























































Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Estate Elite 104711, Инструкция по эксплуатации

Результаты поиска

Содержание Growers Supply GrowSpan Estate Elite 104711

Отзывы:

Бренды по названию

Популярные бренды