Exabyte EZ17A Скачать руководство пользователя страница 99

Страница: 99 / 168

Tape Drive Operation

Installation and Operation

Drive display messages

FORMAT

The drive is repartitioning the tape to the requested format.

WORN TAPE

The tape currently in the drive has exceeded the drive’s maximum
tape passes threshold and must be replaced.

Cleaning messages

CLEAN SOON

The drive should be cleaned at the next convenient time.

CLEANING...

Cleaning is in progress.

DEPLETED

The cleaning tape in the cartridge is depleted and the drive will eject
it. Use a new cleaning cartridge.

CODE LOAD FAIL These messages appear in sequence after the code load failed.

RETRY CODE
LOAD

MAKE
CODELOAD TP

The drive is making a code load tape.

These messages appear w hen non-SmartClean media is used and the drive is cleaned using an Exabyte
Mammoth Cleaning Cartridge.

M 2, M ammoth, and M ammoth-LT drive display messages

Содержание EZ17A









































































































































































Результаты поиска

Содержание EZ17A

Отзывы:

Exabyte EZ17A, Инструкция по установке и эксплуатации, Страница: 99 / 168

Результаты поиска

Содержание EZ17A

Отзывы: