Exabyte EZ17A Скачать руководство пользователя страница 100

Страница: 100 / 168

Chapter 5

Exabyte EZ17M and EZ17A

The following table lists some messages that can appear for the
AIT-2 tape drive.

AIT-2 drive display messages

Tape drive status messages

RdyNoTpe
(Ready-no tape)

The drive is ready to accept a cartridge.

The drive is loading the tape.

Rdy-Out
(Ready out)

The cartridge is ejected from the drive.

RdyTape

(Ready tape)

The drive has successfully loaded the tape and is ready for
read/write operations.

Tape motion messages

Reading

The drive is reading or writing data.

Writing

TpMtion

(Tape in motion)

The drive is moving tape.

Unloadg

(Unloading)

The drive is unloading tape.

Cleaning messages

MustCln

(Must clean)

The drive should be cleaned at the next convenient time.

Clning

(Cleaning)

Cleaning is in progress.

Содержание EZ17A









































































































































































Результаты поиска

Содержание EZ17A

Отзывы:

Exabyte EZ17A, Инструкция по установке и эксплуатации, Страница: 100 / 168

Результаты поиска

Содержание EZ17A

Отзывы: